Month: January 2022

How to reset GE washer front load? It is actually pretty simple to reset the washing machine. However, not many people know how to do that. Learn below what causes the product to need the reset, and what steps you will need to provide in order to make the reset doable.

How to Reset the GE Washer with Front Load

Why reset function is prepared in your washing machine? Actually, if your washing machine works just find how to reset ge washer front load, there is no reason why your GE washer requires a reset.

Turns out the reset function is prepared if the washing machine faces a ‘lock up’. The ‘lock up’ itself means that the washing machine is paused or interrupted forcefully while being in use. This sudden pause or interruption will make the electronic controls to get locked up.

Simply said, your washing machine is ‘confused’ what to do after the interruption. This is where reset function is required to help your washer escape the stuck and lockup.

Well, now you have known that the reset function is prepared if your washing machine is facing a lock up. Then, what may cause the lock up? Here are several conditions which make the washing machine to end up in a locked-up situation.

1. A power failure. A sudden electricity cut will cause the machine’s function to get locked up. Therefore, you will need to reset the washing machine.
2. The washer is stopped even before the ongoing function has been completed. This also will make the machine to end up having a locked-up function. Hence, this calls for a reset.
3. You have a new washer. Resetting the washer will help the machine to be able to use.
4. The pause/stop button is pressed, but later the washer is turned off without continuing the cycle it was in.

If you find out that your washing machine is facing any of the problems mentioned above, then the reset function is a great helper to fix the condition.

Moreover, to reset the GE washing machine, here is the procedure of how to reset GE washer front load that you can do:

1. First, just make sure to cut off all electronic current powering your washing machine. This can be done by unplugging the washer, or simply shutting off the breaker. Do this for around two minutes.
2. If you have a washer with a knob to control the timer, turn it around and then back it to any direction but not the last one. For example, if previously the timer shows 15 minutes left, turn the knob around first, and stop in any minute but not the 15 one.
3. Then, restore the power of your washing machine.
4. The wash cycle needs to be reselected again for that to be able to operate as you wish.

The four steps how to reset GE washer front load procedure mentioned typically will solve the issue. However, if it does not work, calling a professional will be much encouraged.d

Talking about generators, you may think that this item is a great invention to use during a power blackout. However, what if you cannot turn it on? It means your generator will not be able to use. But don’t worry, in this article below, you will find the answer of how to start Coleman Powermate 1850 generator, including some basic information about the generator itself.

About Coleman Powermate 1850 Generator

The name shows it all: power mate. This generator is surely a useful thing when the electricity breaks down or if you are working outside without any reliable electricity sources. Its body may be small to begin with, but you can produce a hefty 1,850 Watt from this unit alone, making it a strong enough buddy to go camping with or if you are using an RV.

Powermate is made by Generac, which is known as a leading manufacturer of various power products. Starting its business in 1959, this company is still running strong for designing and producing great stuff to provide you with the newest technology solutions.

However, it is unfortunate that Coleman Powermate has filed for bankruptcy in 2008, making this brand is no longer producing any generators under that name. However, it does not mean you can’t use any Coleman Powermate generators at all. You can find its secondhand generators instead.

Is that a good generator?—you may ask. According to sources, this generator can be considered as an entry-level generator with inverter and great portability for ones with tight budgets.

People also say that despite the lacking features of what you can obtain from a larger generator. But, remind you about its price. Knowing that, it seems understandable to have the generator lacking features still. If you have just purchased a Coleman Powermate 1850, it’s understandable if you don’t know what to do to turn it on. So, how to start Coleman Powermate 1850 generator?

The answer is pretty simple as what you will find below.

1. First, make sure to put the generator on the ground.
2. Then, prepare oil and fill the oil compartment with the relevant oil.
3. Continue by filling the fuel tank. Typically, generators are using either diesel or gasoline. This Coleman Powermate is using gasoline as its fuel.
4. Make sure to check before turning it on whether there are any loose parts on the unit or not.
5. Also, make sure there are no output electrical appliances attached to the generator before turning it on.
6. Now, you can turn the generator on simply by turning the switch on.

Wondering how to troubleshoot the generator? Here is what you can do:

1. Check for the fuel. If empty, refill it.
2. If there are any loose plugs, make sure to fix it right.
3. Check the level of the generator’s oil.
4. This can be one major yet unrealized problem: the grade of your fuel needs to be more than 85 octanes.
5. Make sure to detach any plugged appliances before trying to run the generator with the switch/rope.
6. Finally, you can try to turn on the generator by pulling the starter rope of the generator sharply—only if the switch isn’t working.

So, that is how to start Coleman Powermate 1850 generator and how to troubleshoot if your generator cannot be turned on. If nothing of the mentioned above works, maybe it’s time to call a professional for some help.

Whirlpool Cabrio Washer is produced by Whirpool, a leading-industry brand in the United States that offers a wide range of washer and dryer. If you own this appliance and find an issue with the lid lock, then you may need the item to be repaired by professional. However, before calling a technician and obtain possibility of paying hefty repairing costs, you may want to consider handling the problem by yourself first. Most of the simple lid lock issues of this product can be solved by following the guide on how to reset Whirlpool Cabrio washer lid lock.

Guide on Resetting and Running Diagnostic Mode of Whirpool Cabrio Washer

Whirlpool Cabrio washer is amongst handful of popular options in the market segment of washing machine. The manufacturer itself is known for its various innovative and advanced technology, such as using LED light display screen, noiseless motor, energy-saving machine, time cycle and temperature settings, and many more.

Top load Whirlpool Cabrio washing machines is one of the most popular item within the wide range of Whirpool provided appliances. Despite its reliability, it is not impossible for the machine to encounter some issues. One of the most common issues experienced by the appliance is related to lid locks, where the lid locks and unlocks, causing the machine to unable to start a cycle.

If you happened to face this problem, then try to follow the guide on how to reset Whirlpool Cabrio washer lid lock below:

1. First and foremost, try to clean the washer because the lid may not engage if it’s in dirty condition and not able to create proper contact with washer’s signal to start a washing cycle. Use rubbing alcohol-dipped cotton swap and clean the areas between the washer and the lid.
2. If the first step doesn’t work, reset the washing machine by unplugging it and plug it back in the electricity.

If the lid produces engaging sounds but still not working, then you may need to run troubleshooting test to see if there’s a more significant problem. Follow the steps below to perform the test:

1. Plug the machine but set it into standby mode, where the indicators will shut down except for ‘Clothes Clean’ or ‘Done’ indicators.
2. Choose any of the available button but don’t press ‘Stop’, ‘Start’ or ‘Power’, and perform the following steps by using that one button:

• Press and holds for about three seconds, and then release for three seconds
• Repeat the previous step for three times
• Release

3. If all indicators are showing active signals for about five seconds and display ‘88’ code as the time remaining information, then you have successfully enter the diagnostic mode
4. If the previous step fails, choose different button to work on the press/hold/release step.
5. After you have entered diagnostic mode and it shows you the error code, save and check the code on the internet to see what repair process your appliance requires.

If you need more detailed helps with troubleshooting procedure, then you may opt for live help in the Whirlpool official website, visit the manufacturer’s service center page, or put an order of lid repair guide from the brand. In the meantime, you may try to the guide on how to reset Whirlpool Cabrio washer lid lock first to see if it works for your machine.

Metal is one of many roofing material options available. It is popular amongst homeowners due to its exceptional durability. The installation process is an essential key to longevity of this particular material, as the most concerning source of possible issue is barely the metal itself, but actually the roofing screws. Find out how and where to place screws on metal roofing correctly below.

Two Ways of Metal Roofing Screw Placement

Incorporating the correct set of equipment is the first step into any proper installation process of metal roofing, which includes screws to anchor the shingles or panels to the roof structure. To make sure that secure seal is created, it is recommended to use properly compressed self-tapping sheet metal screw. The reason why screws work better for metal roofing compared to nails is because they won’t get loose or bend when being exposed to extreme condition such as hot weather, as nails tend to contract and expand frequently.

To install the roof fittingly, you need to know where to place screws on metal roofing. The placement of metal roofing’s screws can be quite challenging, because it depends on the conditions of the metal siding and roofing locations. As if it wasn’t confusing enough, different metal roofing manufacturers may have different manuals and opinions of the right screws placement.

Essentially, however, there are two common methods regarding screw placement of metal roofing. Depending on your certain circumstances, either can be the most appropriate method to choose.

• First method is to install the screws in the higher part of the corrugated metal roofing. This provides of benefits if your location have less debris and less water. However, some may say it offers lower secure connection.
• Second is to install the screws in the lower part of the corrugated panel. This offers an advantage of more secure connection, but it is not ideal if your area is frequently exposed to extreme weather. It also provides the advantages of better compression and less chance of panel distortion when the screws are installed.

As you may have concluded from the above list of methods, in general, you can reap more benefits of installing the screws on the lower part of the rib instead of the top. This ensures a properly tight seal. Moreover, screw installment in the higher part of the panel may cause them to tilt, therefore making the hold stretch out, which will potentially break the installment.

In addition, installing the screw on the higher part of the corrugated metal roof panel provides more risk of pulled out screws when the wind is loud. In terms of easiness, you can also achieve easier installment process if you’re just fastening the screws below panel.

Aside from the placement, it is also important for you to learn about the specific distance it requires for each screw. Commonly, the screws are placed on every third or metal roofing panel’s corrugation. For more detailed where to place screws on metal roofing guide according to the particular conditions of your building and area, you may consult to a roofing professional.

Metal roof insulation is a commonly found element in a lot of private and business building that uses this specific roofing metal. The insulation component helps to eliminate excessive noise and save energy. Even though metal roofing itself has been existed for long time, it is only in recent years that a good percentage of property owners incorporate the insulation. The installation of this feature itself is not really complicated. If you’re interested in DIY-ing the project, here’s a guide on how to install metal roof insulation.

Insulation Installation Guide on New and Existing Metal Roofing

Majority, if not actually all, structure of roofing requires proper insulation, and when it comes to metal roofs, there is no exception either. As stated above, plenty of residential and commercial buildings are equipped with insulation to decrease noise pollution and increase energy conservation. It is definitely worth to install the insulation of metal roof if you want a cozy, quite, and warm dwelling space.

Hiring a professional is what some homeowners prefer, but that doesn’t mean it is rare to find some of them install it by themselves. Whether you are going to install the insulation on an existing or new roof structure, you can follow the helpful guides on how to install metal roof insulation below.

Steps to install insulation for new metal roof:

1. Use and set plywood for the rood sheathing by placing it upstanding to the roof joist and fastening the nails into the roof structure.
2. Lay out building paper layers on top of the sheathing. Make sure you provide six inches distance between the layers and fasten it using staples or nails to prevent leaks and moisture.
3. Spray or set the foam insulation on the whole roof surface. Position the sheets to be near each other but not to the point of overlapping.
4. Seal the seams by using duct tape and to provide extra protection against leaks or moisture.
5. Install your metal roof panels on top of the insulation layer based on the instruction from the manufacturer.

Steps to install insulation for existing metal roof:

1. Check the metal roof’s underside from the building attic until you spot the plywood roof sheathing layer that upheld by framing platform. The angled and larger-sized beams are referred to as joists, while the horizontal and smaller-sized ones are referred to as purlins.
2. Locate the fiberglass batt insulation on any open space between the purlins and the sheathing that you can find. Note that you may create less effective insulation if you locate them over tightly, so try to fill the gaps loosely.
3. Use rigid foam insulation to conceal the extent of your roof sheathing. Make sure it fit first by cutting the sit into proper size and use adhesive or staples to fasten it to the place.

As long as you incorporate good-quality materials and appropriate equipment and tools, it is not actually hard to set insulation under the metal roofing. However, if you aren’t sure that you can execute the work properly even after reading the guide on how to install metal roof insulation provided above, then it’s highly recommended to get help from expert insulation installers than can ensure success and safety of the project.